PIC16F15354 | ||||
---|---|---|---|---|
CONFIG1 (address:0x8007, mask:0x2977, default:0x2977) | ||||
FEXTOSC -- External Oscillator mode selection bits (bitmask:0x0007) | ||||
FEXTOSC = LP | 0x3FF8 | LP (crystal oscillator) optimized for 32.768kHz; PFM set to low power. | ||
FEXTOSC = XT | 0x3FF9 | XT (crystal oscillator) above 500kHz, below 4MHz; PFM set to medium power. | ||
FEXTOSC = HS | 0x3FFA | HS (crystal oscillator) above 4MHz; PFM set to high power. | ||
FEXTOSC = Reserved | 0x3FFB | Reserved. | ||
FEXTOSC = OFF | 0x3FFC | Oscillator not enabled. | ||
FEXTOSC = ECL | 0x3FFD | EC below 500kHz; PFM set to low power. | ||
FEXTOSC = ECM | 0x3FFE | EC for 500kHz to 8MHz; PFM set to medium power. | ||
FEXTOSC = ECH | 0x3FFF | EC above 8MHz; PFM set to high power. | ||
RSTOSC -- Power-up default value for COSC bits (bitmask:0x0070) | ||||
RSTOSC = HFINT32 | 0x3F8F | HFINTOSC with OSCFRQ= 32 MHz and CDIV = 1:1. | ||
RSTOSC = HFINTPLL | 0x3F9F | HFINTOSC with 2x PLL, with OSCFRQ = 16 MHz and CDIV = 1:1 (FOSC = 32 MHz). | ||
RSTOSC = EXT4X | 0x3FAF | EXTOSC with 4x PLL, with EXTOSC operating per FEXTOSC bits. | ||
RSTOSC = Reserved | 0x3FBF | Reserved. | ||
RSTOSC = SOSC | 0x3FCF | SOSC. | ||
RSTOSC = LFINT | 0x3FDF | LFINTOSC. | ||
RSTOSC = HFINT1 | 0x3FEF | HFINTOSC (1MHz). | ||
RSTOSC = EXT1X | 0x3FFF | EXTOSC operating per FEXTOSC bits. | ||
CLKOUTEN -- Clock Out Enable bit (bitmask:0x0100) | ||||
CLKOUTEN = ON | 0x3EFF | CLKOUT function is enabled; FOSC/4 clock appears at OSC2. | ||
CLKOUTEN = OFF | 0x3FFF | CLKOUT function is disabled; i/o or oscillator function on OSC2. | ||
CSWEN -- Clock Switch Enable bit (bitmask:0x0800) | ||||
CSWEN = OFF | 0x37FF | The NOSC and NDIV bits cannot be changed by user software. | ||
CSWEN = ON | 0x3FFF | Writing to NOSC and NDIV is allowed. | ||
FCMEN -- Fail-Safe Clock Monitor Enable bit (bitmask:0x2000) | ||||
FCMEN = OFF | 0x1FFF | FSCM timer disabled. | ||
FCMEN = ON | 0x3FFF | FSCM timer enabled. | ||
CONFIG2 (address:0x8008, mask:0x3EE3, default:0x3EE3) | ||||
MCLRE -- Master Clear Enable bit (bitmask:0x0001) | ||||
MCLRE = OFF | 0x3FFE | MCLR pin function is port defined function. | ||
MCLRE = ON | 0x3FFF | MCLR pin is Master Clear function. | ||
PWRTE -- Power-up Timer Enable bit (bitmask:0x0002) | ||||
PWRTE = ON | 0x3FFD | PWRT enabled. | ||
PWRTE = OFF | 0x3FFF | PWRT disabled. | ||
LPBOREN -- Low-Power BOR enable bit (bitmask:0x0020) | ||||
LPBOREN = ON | 0x3FDF | ULPBOR enabled. | ||
LPBOREN = OFF | 0x3FFF | ULPBOR disabled. | ||
BOREN -- Brown-out reset enable bits (bitmask:0x00C0) | ||||
BOREN = OFF | 0x3F3F | Brown-out reset disabled. | ||
BOREN = SBOREN | 0x3F7F | Brown-out reset enabled according to SBOREN bit. | ||
BOREN = NSLEEP | 0x3FBF | Brown-out Reset enabled while running, disabled in sleep; SBOREN is ignored. | ||
BOREN = ON | 0x3FFF | Brown-out Reset Enabled, SBOREN bit is ignored. | ||
BORV -- Brown-out Reset Voltage Selection (bitmask:0x0200) | ||||
BORV = HI | 0x3DFF | Brown-out Reset Voltage (VBOR) is set to 2.7V. | ||
BORV = LO | 0x3FFF | Brown-out Reset Voltage (VBOR) set to 1.9V on LF, and 2.45V on F Devices. | ||
ZCD -- Zero-cross detect disable (bitmask:0x0400) | ||||
ZCD = ON | 0x3BFF | Zero-cross detect circuit is always enabled. | ||
ZCD = OFF | 0x3FFF | Zero-cross detect circuit is disabled at POR. | ||
PPS1WAY -- Peripheral Pin Select one-way control (bitmask:0x0800) | ||||
PPS1WAY = OFF | 0x37FF | The PPSLOCK bit can be set and cleared repeatedly by software. | ||
PPS1WAY = ON | 0x3FFF | The PPSLOCK bit can be cleared and set only once in software. | ||
STVREN -- Stack Overflow/Underflow Reset Enable bit (bitmask:0x1000) | ||||
STVREN = OFF | 0x2FFF | Stack Overflow or Underflow will not cause a reset. | ||
STVREN = ON | 0x3FFF | Stack Overflow or Underflow will cause a reset. | ||
DEBUG -- Debugger enable bit (bitmask:0x2000) | ||||
DEBUG = ON | 0x1FFF | Background debugger enabled. | ||
DEBUG = OFF | 0x3FFF | Background debugger disabled. | ||
CONFIG3 (address:0x8009, mask:0x3F7F, default:0x3F7F) | ||||
WDTCPS -- WDT Period Select bits (bitmask:0x001F) | ||||
WDTCPS = WDTCPS_0 | 0x3FE0 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_1 | 0x3FE1 | Divider ratio 1:64. | ||
WDTCPS = WDTCPS_2 | 0x3FE2 | Divider ratio 1:128. | ||
WDTCPS = WDTCPS_3 | 0x3FE3 | Divider ratio 1:256. | ||
WDTCPS = WDTCPS_4 | 0x3FE4 | Divider ratio 1:512. | ||
WDTCPS = WDTCPS_5 | 0x3FE5 | Divider ratio 1:1024. | ||
WDTCPS = WDTCPS_6 | 0x3FE6 | Divider ratio 1:2048. | ||
WDTCPS = WDTCPS_7 | 0x3FE7 | Divider ratio 1:4096. | ||
WDTCPS = WDTCPS_8 | 0x3FE8 | Divider ratio 1:8192. | ||
WDTCPS = WDTCPS_9 | 0x3FE9 | Divider ratio 1:16384. | ||
WDTCPS = WDTCPS_10 | 0x3FEA | Divider ratio 1:32768. | ||
WDTCPS = WDTCPS_11 | 0x3FEB | Divider ratio 1:65536. | ||
WDTCPS = WDTCPS_12 | 0x3FEC | Divider ratio 1:131072. | ||
WDTCPS = WDTCPS_13 | 0x3FED | Divider ratio 1:262144. | ||
WDTCPS = WDTCPS_14 | 0x3FEE | Divider ratio 1:524299. | ||
WDTCPS = WDTCPS_15 | 0x3FEF | Divider ratio 1:1048576. | ||
WDTCPS = WDTCPS_16 | 0x3FF0 | Divider ratio 1:2097152. | ||
WDTCPS = WDTCPS_17 | 0x3FF1 | Divider ratio 1:4194304. | ||
WDTCPS = WDTCPS_18 | 0x3FF2 | Divider ratio 1:8388608. | ||
WDTCPS = WDTCPS_19 | 0x3FF3 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_20 | 0x3FF4 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_21 | 0x3FF5 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_22 | 0x3FF6 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_23 | 0x3FF7 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_24 | 0x3FF8 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_25 | 0x3FF9 | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_26 | 0x3FFA | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_27 | 0x3FFB | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_28 | 0x3FFC | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_29 | 0x3FFD | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_30 | 0x3FFE | Divider ratio 1:32. | ||
WDTCPS = WDTCPS_31 | 0x3FFF | Divider ratio 1:65536; software control of WDTPS. | ||
WDTE -- WDT operating mode (bitmask:0x0060) | ||||
WDTE = OFF | 0x3F9F | WDT Disabled, SWDTEN is ignored. | ||
WDTE = SWDTEN | 0x3FBF | WDT enabled/disabled by SWDTEN bit in WDTCON0. | ||
WDTE = NSLEEP | 0x3FDF | WDT enabled while sleep=0, suspended when sleep=1; SWDTEN ignored. | ||
WDTE = ON | 0x3FFF | WDT enabled regardless of sleep; SWDTEN ignored. | ||
WDTCWS -- WDT Window Select bits (bitmask:0x0700) | ||||
WDTCWS = WDTCWS_0 | 0x38FF | window delay = 87.5 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_1 | 0x39FF | window delay = 75 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_2 | 0x3AFF | window delay = 62.5 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_3 | 0x3BFF | window delay = 50 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_4 | 0x3CFF | window delay = 37.5 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_5 | 0x3DFF | window delay = 25 percent of time; no software control; keyed access required. | ||
WDTCWS = WDTCWS_6 | 0x3EFF | window always open (100%); no software control; keyed access required. | ||
WDTCWS = WDTCWS_7 | 0x3FFF | window always open (100%); software control; keyed access not required. | ||
WDTCCS -- WDT input clock selector (bitmask:0x3800) | ||||
WDTCCS = LFINTOSC | 0x07FF | WDT reference clock is the 31.0kHz LFINTOSC output. | ||
WDTCCS = HFINTOSC | 0x0FFF | WDT reference clock is the 31.25 kHz HFINTOSC. | ||
WDTCCS = SOSC | 0x17FF | WDT reference clock is the 32kHz secondary oscillator. | ||
WDTCCS = SC | 0x3FFF | Software Control. | ||
CONFIG4 (address:0x800A, mask:0x2B9F, default:0x2B9F) | ||||
BBSIZE -- Boot Block Size Selection bits (bitmask:0x0007) | ||||
BBSIZE = BB64K | 0x3FF8 | * half of user program memory. | ||
BBSIZE = BB32K | 0x3FF9 | * half of user program memory. | ||
BBSIZE = BB16K | 0x3FFA | * half of user program memory. | ||
BBSIZE = BB8K | 0x3FFB | * half of user program memory. | ||
BBSIZE = BB4K | 0x3FFC | 4096 words boot block size. | ||
BBSIZE = BB2K | 0x3FFD | 2048 words boot block size. | ||
BBSIZE = BB1K | 0x3FFE | 1024 words boot block size. | ||
BBSIZE = BB512 | 0x3FFF | 512 words boot block size. | ||
BBEN -- Boot Block Enable bit (bitmask:0x0008) | ||||
BBEN = ON | 0x3FF7 | Boot Block enabled. | ||
BBEN = OFF | 0x3FFF | Boot Block disabled. | ||
SAFEN -- SAF Enable bit (bitmask:0x0010) | ||||
SAFEN = ON | 0x3FEF | SAF enabled. | ||
SAFEN = OFF | 0x3FFF | SAF disabled. | ||
WRTAPP -- Application Block Write Protection bit (bitmask:0x0080) | ||||
WRTAPP = ON | 0x3F7F | Application Block write protected. | ||
WRTAPP = OFF | 0x3FFF | Application Block not write protected. | ||
WRTB -- Boot Block Write Protection bit (bitmask:0x0100) | ||||
WRTB = ON | 0x3EFF | Boot Block write protected. | ||
WRTB = OFF | 0x3FFF | Boot Block not write protected. | ||
WRTC -- Configuration Register Write Protection bit (bitmask:0x0200) | ||||
WRTC = ON | 0x3DFF | Configuration Register write protected. | ||
WRTC = OFF | 0x3FFF | Configuration Register not write protected. | ||
WRTSAF -- Storage Area Flash Write Protection bit (bitmask:0x0800) | ||||
WRTSAF = ON | 0x37FF | SAF write protected. | ||
WRTSAF = OFF | 0x3FFF | SAF not write protected. | ||
LVP -- Low Voltage Programming Enable bit (bitmask:0x2000) | ||||
LVP = OFF | 0x1FFF | High Voltage on MCLR/Vpp must be used for programming. | ||
LVP = ON | 0x3FFF | Low Voltage programming enabled. MCLR/Vpp pin function is MCLR. | ||
CONFIG5 (address:0x800B, mask:0x0001, default:0x0001) | ||||
CP -- UserNVM Program memory code protection bit (bitmask:0x0001) | ||||
CP = ON | 0x3FFE | UserNVM code protection enabled. | ||
CP = OFF | 0x3FFF | UserNVM code protection disabled. |
This page generated automatically by the device-help.pl program (2017-05-13 09:29:47 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.