PIC16F1615

PIC16F1615

CONFIG1 (address:0x8007, mask:0x3EE7, default:0x3EE7)

FOSC -- Oscillator Selection Bits (bitmask:0x0007)
FOSC = HS	0x3FFA	HS Oscillator, High-speed crystal/resonator connected between OSC1 and OSC2 pins.
FOSC = INTOSC	0x3FFC	INTOSC oscillator: I/O function on CLKIN pin.
FOSC = ECL	0x3FFD	ECL, External Clock, Low Power Mode (0-0.5 MHz): device clock supplied to CLKIN pins.
FOSC = ECM	0x3FFE	ECM, External Clock, Medium Power Mode (0.5-4 MHz): device clock supplied to CLKIN pins.
FOSC = ECH	0x3FFF	ECH, External Clock, High Power Mode (4-20 MHz): device clock supplied to CLKIN pins.

PWRTE -- Power-up Timer Enable (bitmask:0x0020)
PWRTE = ON	0x3FDF	PWRT enabled.
PWRTE = OFF	0x3FFF	PWRT disabled.

MCLRE -- MCLR Pin Function Select (bitmask:0x0040)
MCLRE = OFF	0x3FBF	MCLR/VPP pin function is digital input.
MCLRE = ON	0x3FFF	MCLR/VPP pin function is MCLR.

CP -- Flash Program Memory Code Protection (bitmask:0x0080)
CP = ON	0x3F7F	Program memory code protection is enabled.
CP = OFF	0x3FFF	Program memory code protection is disabled.

BOREN -- Brown-out Reset Enable (bitmask:0x0600)
BOREN = OFF	0x39FF	Brown-out Reset disabled.
BOREN = SBODEN	0x3BFF	Brown-out Reset controlled by the SBOREN bit in the BORCON register.
BOREN = NSLEEP	0x3DFF	Brown-out Reset enabled while running and disabled in Sleep.
BOREN = ON	0x3FFF	Brown-out Reset enabled.

CLKOUTEN -- Clock Out Enable (bitmask:0x0800)
CLKOUTEN = ON	0x37FF	CLKOUT function is enabled on the CLKOUT pin.
CLKOUTEN = OFF	0x3FFF	CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin.

IESO -- Internal/External Switch Over (bitmask:0x1000)
IESO = OFF	0x2FFF	Internal External Switch Over mode is disabled.
IESO = ON	0x3FFF	Internal External Switch Over mode is enabled.

FCMEN -- Fail-Safe Clock Monitor Enable (bitmask:0x2000)
FCMEN = OFF	0x1FFF	Fail-Safe Clock Monitor is disabled.
FCMEN = ON	0x3FFF	Fail-Safe Clock Monitor is enabled.

CONFIG2 (address:0x8008, mask:0x3F87, default:0x3F87)

WRT -- Flash Memory Self-Write Protection (bitmask:0x0003)
WRT = ALL	0x3FFC	000h to 1FFFh write protected, no addresses may be modified by PMCON control.
WRT = HALF	0x3FFD	000h to FFFh write protected, 1000h to 1FFFh may be modified by PMCON control.
WRT = BOOT	0x3FFE	000h to 1FFh write protected, 200h to 1FFFh may be modified by PMCON control.
WRT = OFF	0x3FFF	Write protection off.

PPS1WAY -- Peripheral Pin Select one-way control (bitmask:0x0004)
PPS1WAY = OFF	0x3FFB	The PPSLOCK bit can be set and cleared repeatedly by software.
PPS1WAY = ON	0x3FFF	The PPSLOCK bit cannot be cleared once it is set by software.

ZCD -- Zero Cross Detect Disable Bit (bitmask:0x0080)
ZCD = ON	0x3F7F	ZCD always enabled.
ZCD = OFF	0x3FFF	ZCD disable. ZCD can be enabled by setting the ZCDSEN bit of ZCDCON.

PLLEN -- PLL Enable Bit (bitmask:0x0100)
PLLEN = OFF	0x3EFF	4x PLL is enabled when software sets the SPLLEN bit.
PLLEN = ON	0x3FFF	4x PLL is always enabled.

STVREN -- Stack Overflow/Underflow Reset Enable (bitmask:0x0200)
STVREN = OFF	0x3DFF	Stack Overflow or Underflow will not cause a Reset.
STVREN = ON	0x3FFF	Stack Overflow or Underflow will cause a Reset.

BORV -- Brown-out Reset Voltage Selection (bitmask:0x0400)
BORV = HI	0x3BFF	Brown-out Reset Voltage (Vbor), high trip point selected.
BORV = LO	0x3FFF	Brown-out Reset Voltage (Vbor), low trip point selected.

LPBOR -- Low-Power Brown Out Reset (bitmask:0x0800)
LPBOR = ON	0x37FF	Low-Power BOR is enabled.
LPBOR = OFF	0x3FFF	Low-Power BOR is disabled.

DEBUG -- Debugger enable bit (bitmask:0x1000)
DEBUG = ON	0x2FFF	Background debugger enabled.
DEBUG = OFF	0x3FFF	Background debugger disabled.

LVP -- Low-Voltage Programming Enable (bitmask:0x2000)
LVP = OFF	0x1FFF	High-voltage on MCLR/VPP must be used for programming.
LVP = ON	0x3FFF	Low-voltage programming enabled.

CONFIG3 (address:0x8009, mask:0x3F7F, default:0x3F7F)

WDTCPS -- WDT Period Select (bitmask:0x001F)
WDTCPS = WDTCPS0	0x3FE0	1:32 (1 ms period).
WDTCPS = WDTCPS1	0x3FE1	1:64 (2 ms period).
WDTCPS = WDTCPS2	0x3FE2	1:128 (4 ms period).
WDTCPS = WDTCPS3	0x3FE3	1:256 (8 ms period).
WDTCPS = WDTCPS4	0x3FE4	1:512 (16 ms period).
WDTCPS = WDTCPS5	0x3FE5	1:1024 (32 ms period).
WDTCPS = WDTCPS6	0x3FE6	1:2048 (64 ms period).
WDTCPS = WDTCPS7	0x3FE7	1:4096 (128 ms period).
WDTCPS = WDTCPS8	0x3FE8	1:8192 (256 ms period).
WDTCPS = WDTCPS9	0x3FE9	1:16384 (512 ms period).
WDTCPS = WDTCPSA	0x3FEA	1:32768 (1 s period).
WDTCPS = WDTCPSB	0x3FEB	1:65536 (2 s period).
WDTCPS = WDTCPSC	0x3FEC	1:131072 (4 s period).
WDTCPS = WDTCPSD	0x3FED	1:262144 (8 s period).
WDTCPS = WDTCPSE	0x3FEE	1:524299 (16 s period).
WDTCPS = WDTCPSF	0x3FEF	1:1048576 (32 s period).
WDTCPS = WDTCPS10	0x3FF0	1:2097152 (64 s period).
WDTCPS = WDTCPS11	0x3FF1	1:4194304 (128 s period).
WDTCPS = WDTCPS12	0x3FF2	1:8388608 (256 s period).
WDTCPS = WDTCPS1F	0x3FFF	Software Control (WDTPS).

WDTE -- Watchdog Timer Enable (bitmask:0x0060)
WDTE = OFF	0x3F9F	WDT disabled.
WDTE = SWDTEN	0x3FBF	WDT controlled by the SWDTEN bit in the WDTCON register.
WDTE = NSLEEP	0x3FDF	WDT enabled while running and disabled in Sleep.
WDTE = ON	0x3FFF	WDT enabled.

WDTCWS -- WDT Window Select (bitmask:0x0700)
WDTCWS = WDTCWS125	0x38FF	12.5 percent window open time.
WDTCWS = WDTCWS25	0x39FF	25 percent window open time.
WDTCWS = WDTCWS375	0x3AFF	37.5 percent window open time.
WDTCWS = WDTCWS50	0x3BFF	50 percent window open time.
WDTCWS = WDTCWS625	0x3CFF	62.5 percent window open time.
WDTCWS = WDTCWS75	0x3DFF	75 percent window open time.
WDTCWS = WDTCWS100	0x3EFF	100 percent window open time (Legacy WDT) .
WDTCWS = WDTCWSSW	0x3FFF	Software WDT window size control (WDTWS bits).

WDTCCS -- WDT Input Clock Selector (bitmask:0x3800)
WDTCCS = LFINTOSC	0x07FF	31.0kHz LFINTOSC.
WDTCCS = MFINTOSC	0x0FFF	31.25 kHz HFINTOSC (MFINTOSC).
WDTCCS = SWC	0x3FFF	Software control, controlled by WDTCS bits.

CONFIG1 (address:0x8007, mask:0x3EE7, default:0x3EE7)

FOSC -- Oscillator Selection Bits (bitmask:0x0007)

FOSC = HS

0x3FFA

HS Oscillator, High-speed crystal/resonator connected between OSC1 and OSC2 pins.

FOSC = INTOSC

0x3FFC

INTOSC oscillator: I/O function on CLKIN pin.

FOSC = ECL

0x3FFD

ECL, External Clock, Low Power Mode (0-0.5 MHz): device clock supplied to CLKIN pins.

FOSC = ECM

0x3FFE

ECM, External Clock, Medium Power Mode (0.5-4 MHz): device clock supplied to CLKIN pins.

FOSC = ECH

0x3FFF

ECH, External Clock, High Power Mode (4-20 MHz): device clock supplied to CLKIN pins.

PWRTE -- Power-up Timer Enable (bitmask:0x0020)

PWRTE = ON

0x3FDF

PWRT enabled.

PWRTE = OFF

0x3FFF

PWRT disabled.

MCLRE -- MCLR Pin Function Select (bitmask:0x0040)

MCLRE = OFF

0x3FBF

MCLR/VPP pin function is digital input.

MCLRE = ON

0x3FFF

MCLR/VPP pin function is MCLR.

CP -- Flash Program Memory Code Protection (bitmask:0x0080)

CP = ON

0x3F7F

Program memory code protection is enabled.

CP = OFF

0x3FFF

Program memory code protection is disabled.

BOREN -- Brown-out Reset Enable (bitmask:0x0600)

BOREN = OFF

0x39FF

Brown-out Reset disabled.

BOREN = SBODEN

0x3BFF

Brown-out Reset controlled by the SBOREN bit in the BORCON register.

BOREN = NSLEEP

0x3DFF

Brown-out Reset enabled while running and disabled in Sleep.

BOREN = ON

0x3FFF

Brown-out Reset enabled.

CLKOUTEN -- Clock Out Enable (bitmask:0x0800)

CLKOUTEN = ON

0x37FF

CLKOUT function is enabled on the CLKOUT pin.

CLKOUTEN = OFF

0x3FFF

CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin.

IESO -- Internal/External Switch Over (bitmask:0x1000)

IESO = OFF

0x2FFF

Internal External Switch Over mode is disabled.

IESO = ON

0x3FFF

Internal External Switch Over mode is enabled.

FCMEN -- Fail-Safe Clock Monitor Enable (bitmask:0x2000)

FCMEN = OFF

0x1FFF

Fail-Safe Clock Monitor is disabled.

FCMEN = ON

0x3FFF

Fail-Safe Clock Monitor is enabled.

CONFIG2 (address:0x8008, mask:0x3F87, default:0x3F87)

WRT -- Flash Memory Self-Write Protection (bitmask:0x0003)

WRT = ALL

0x3FFC

000h to 1FFFh write protected, no addresses may be modified by PMCON control.

WRT = HALF

0x3FFD

000h to FFFh write protected, 1000h to 1FFFh may be modified by PMCON control.

WRT = BOOT

0x3FFE

000h to 1FFh write protected, 200h to 1FFFh may be modified by PMCON control.

WRT = OFF

0x3FFF

Write protection off.

PPS1WAY -- Peripheral Pin Select one-way control (bitmask:0x0004)

PPS1WAY = OFF

0x3FFB

The PPSLOCK bit can be set and cleared repeatedly by software.

PPS1WAY = ON

0x3FFF

The PPSLOCK bit cannot be cleared once it is set by software.

ZCD -- Zero Cross Detect Disable Bit (bitmask:0x0080)

ZCD = ON

0x3F7F

ZCD always enabled.

ZCD = OFF

0x3FFF

ZCD disable. ZCD can be enabled by setting the ZCDSEN bit of ZCDCON.

PLLEN -- PLL Enable Bit (bitmask:0x0100)

PLLEN = OFF

0x3EFF

4x PLL is enabled when software sets the SPLLEN bit.

PLLEN = ON

0x3FFF

4x PLL is always enabled.

STVREN -- Stack Overflow/Underflow Reset Enable (bitmask:0x0200)

STVREN = OFF

0x3DFF

Stack Overflow or Underflow will not cause a Reset.

STVREN = ON

0x3FFF

Stack Overflow or Underflow will cause a Reset.

BORV -- Brown-out Reset Voltage Selection (bitmask:0x0400)

BORV = HI

0x3BFF

Brown-out Reset Voltage (Vbor), high trip point selected.

BORV = LO

0x3FFF

Brown-out Reset Voltage (Vbor), low trip point selected.

LPBOR -- Low-Power Brown Out Reset (bitmask:0x0800)

LPBOR = ON

0x37FF

Low-Power BOR is enabled.

LPBOR = OFF

0x3FFF

Low-Power BOR is disabled.

DEBUG -- Debugger enable bit (bitmask:0x1000)

DEBUG = ON

0x2FFF

Background debugger enabled.

DEBUG = OFF

0x3FFF

Background debugger disabled.

LVP -- Low-Voltage Programming Enable (bitmask:0x2000)

LVP = OFF

0x1FFF

High-voltage on MCLR/VPP must be used for programming.

LVP = ON

0x3FFF

Low-voltage programming enabled.

CONFIG3 (address:0x8009, mask:0x3F7F, default:0x3F7F)

WDTCPS -- WDT Period Select (bitmask:0x001F)

WDTCPS = WDTCPS0

0x3FE0

1:32 (1 ms period).

WDTCPS = WDTCPS1

0x3FE1

1:64 (2 ms period).

WDTCPS = WDTCPS2

0x3FE2

1:128 (4 ms period).

WDTCPS = WDTCPS3

0x3FE3

1:256 (8 ms period).

WDTCPS = WDTCPS4

0x3FE4

1:512 (16 ms period).

WDTCPS = WDTCPS5

0x3FE5

1:1024 (32 ms period).

WDTCPS = WDTCPS6

0x3FE6

1:2048 (64 ms period).

WDTCPS = WDTCPS7

0x3FE7

1:4096 (128 ms period).

WDTCPS = WDTCPS8

0x3FE8

1:8192 (256 ms period).

WDTCPS = WDTCPS9

0x3FE9

1:16384 (512 ms period).

WDTCPS = WDTCPSA

0x3FEA

1:32768 (1 s period).

WDTCPS = WDTCPSB

0x3FEB

1:65536 (2 s period).

WDTCPS = WDTCPSC

0x3FEC

1:131072 (4 s period).

WDTCPS = WDTCPSD

0x3FED

1:262144 (8 s period).

WDTCPS = WDTCPSE

0x3FEE

1:524299 (16 s period).

WDTCPS = WDTCPSF

0x3FEF

1:1048576 (32 s period).

WDTCPS = WDTCPS10

0x3FF0

1:2097152 (64 s period).

WDTCPS = WDTCPS11

0x3FF1

1:4194304 (128 s period).

WDTCPS = WDTCPS12

0x3FF2

1:8388608 (256 s period).

WDTCPS = WDTCPS1F

0x3FFF

Software Control (WDTPS).

WDTE -- Watchdog Timer Enable (bitmask:0x0060)

WDTE = OFF

0x3F9F

WDT disabled.

WDTE = SWDTEN

0x3FBF

WDT controlled by the SWDTEN bit in the WDTCON register.

WDTE = NSLEEP

0x3FDF

WDT enabled while running and disabled in Sleep.

WDTE = ON

0x3FFF

WDT enabled.

WDTCWS -- WDT Window Select (bitmask:0x0700)

WDTCWS = WDTCWS125

0x38FF

12.5 percent window open time.

WDTCWS = WDTCWS25

0x39FF

25 percent window open time.

WDTCWS = WDTCWS375

0x3AFF

37.5 percent window open time.

WDTCWS = WDTCWS50

0x3BFF

50 percent window open time.

WDTCWS = WDTCWS625

0x3CFF

62.5 percent window open time.

WDTCWS = WDTCWS75

0x3DFF

75 percent window open time.

WDTCWS = WDTCWS100

0x3EFF

100 percent window open time (Legacy WDT) .

WDTCWS = WDTCWSSW

0x3FFF

Software WDT window size control (WDTWS bits).

WDTCCS -- WDT Input Clock Selector (bitmask:0x3800)

WDTCCS = LFINTOSC

0x07FF

31.0kHz LFINTOSC.

WDTCCS = MFINTOSC

0x0FFF

31.25 kHz HFINTOSC (MFINTOSC).

WDTCCS = SWC

0x3FFF

Software control, controlled by WDTCS bits.

This page generated automatically by the device-help.pl program (2017-05-13 09:29:46 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.