| PIC16F19197 | ||||
|---|---|---|---|---|
| CONFIG1 (address:0x8007, mask:0x2F77, default:0x2F77) | ||||
| FEXTOSC -- External Oscillator mode selection bits (bitmask:0x0007) | ||||
| FEXTOSC = OFF | 0x3FF8 | Oscillator not enabled. | ||
| FEXTOSC = ECL | 0x3FFD | EC below 500kHz; PFM set to low power. | ||
| FEXTOSC = ECM | 0x3FFE | EC for 500kHz to 8MHz; PFM set to medium power. | ||
| FEXTOSC = ECH | 0x3FFF | EC above 8MHz; PFM set to high power. | ||
| RSTOSC -- Power-up default value for COSC bits (bitmask:0x0070) | ||||
| RSTOSC = HFINT32 | 0x3F8F | HFINTOSC with OSCFRQ= 32 MHz and CDIV = 1:1. | ||
| RSTOSC = HFINTPLL | 0x3F9F | HFINTOSC with 2x PLL, with OSCFRQ = 16 MHz and CDIV = 1:1 (FOSC = 32 MHz). | ||
| RSTOSC = EXT4X | 0x3FAF | EXTOSC with 4x PLL, with EXTOSC operating per FEXTOSC bits. | ||
| RSTOSC = Reserved | 0x3FBF | Reserved. | ||
| RSTOSC = SOSC | 0x3FCF | SOSC. | ||
| RSTOSC = LFINT | 0x3FDF | LFINTOSC. | ||
| RSTOSC = HFINT1 | 0x3FEF | HFINTOSC (1MHz). | ||
| RSTOSC = EXT1X | 0x3FFF | EXTOSC operating per FEXTOSC bits. | ||
| CLKOUTEN -- Clock Out Enable bit (bitmask:0x0100) | ||||
| CLKOUTEN = ON | 0x3EFF | CLKOUT function is enabled; FOSC/4 clock appears at OSC2. | ||
| CLKOUTEN = OFF | 0x3FFF | CLKOUT function is disabled; i/o or oscillator function on OSC2. | ||
| VBATEN -- VBAT Pin Enable bit (bitmask:0x0200) | ||||
| VBATEN = ON | 0x3DFF | VBAT functionality is enabled. | ||
| VBATEN = OFF | 0x3FFF | VBAT functionality is disabled. | ||
| LCDPEN -- LCD Charge Pump Mode bit (bitmask:0x0400) | ||||
| LCDPEN = OFF | 0x3BFF | LCD Charge Pump is disabled. | ||
| LCDPEN = ON | 0x3FFF | LCD Charge Pump is enabled. | ||
| CSWEN -- Clock Switch Enable bit (bitmask:0x0800) | ||||
| CSWEN = OFF | 0x37FF | The NOSC and NDIV bits cannot be changed by user software. | ||
| CSWEN = ON | 0x3FFF | Writing to NOSC and NDIV is allowed. | ||
| FCMEN -- Fail-Safe Clock Monitor Enable bit (bitmask:0x2000) | ||||
| FCMEN = OFF | 0x1FFF | FSCM timer disabled. | ||
| FCMEN = ON | 0x3FFF | FSCM timer enabled. | ||
| CONFIG2 (address:0x8008, mask:0x3EE7, default:0x3EE7) | ||||
| MCLRE -- Master Clear Enable bit (bitmask:0x0001) | ||||
| MCLRE = OFF | 0x3FFE | MCLR pin function is port defined function. | ||
| MCLRE = ON | 0x3FFF | MCLR pin is Master Clear function. | ||
| PWRTE -- Power-up Timer selection bits (bitmask:0x0006) | ||||
| PWRTE = PWRT_1 | 0x3FF9 | PWRT set at 1 ms. | ||
| PWRTE = PWRT_16 | 0x3FFB | PWRT set at 16 ms. | ||
| PWRTE = PWRT_64 | 0x3FFD | PWRT set at 64 ms. | ||
| PWRTE = OFF | 0x3FFF | PWRT disable. | ||
| LPBOREN -- Low-Power BOR enable bit (bitmask:0x0020) | ||||
| LPBOREN = ON | 0x3FDF | ULPBOR enabled. | ||
| LPBOREN = OFF | 0x3FFF | ULPBOR disabled. | ||
| BOREN -- Brown-out reset enable bits (bitmask:0x00C0) | ||||
| BOREN = OFF | 0x3F3F | Brown-out reset disabled. | ||
| BOREN = SBOREN | 0x3F7F | Brown-out reset enabled according to SBOREN bit. | ||
| BOREN = NSLEEP | 0x3FBF | Brown-out Reset enabled while running, disabled in sleep; SBOREN is ignored. | ||
| BOREN = ON | 0x3FFF | Brown-out Reset Enabled, SBOREN bit is ignored. | ||
| BORV -- Brown-out Reset Voltage Selection (bitmask:0x0200) | ||||
| BORV = HI | 0x3DFF | Brown-out Reset Voltage (VBOR) is set to 2.7V. | ||
| BORV = LO | 0x3FFF | Brown-out Reset Voltage (VBOR) set to 1.9V on LF, and 2.45V on F Devices. | ||
| ZCD -- Zero-cross detect disable (bitmask:0x0400) | ||||
| ZCD = ON | 0x3BFF | Zero-cross detect circuit is always enabled. | ||
| ZCD = OFF | 0x3FFF | Zero-cross detect circuit is disabled at POR. | ||
| PPS1WAY -- Peripheral Pin Select one-way control (bitmask:0x0800) | ||||
| PPS1WAY = OFF | 0x37FF | The PPSLOCK bit can be set and cleared repeatedly by software. | ||
| PPS1WAY = ON | 0x3FFF | The PPSLOCK bit can be cleared and set only once in software. | ||
| STVREN -- Stack Overflow/Underflow Reset Enable bit (bitmask:0x1000) | ||||
| STVREN = OFF | 0x2FFF | Stack Overflow or Underflow will not cause a reset. | ||
| STVREN = ON | 0x3FFF | Stack Overflow or Underflow will cause a reset. | ||
| DEBUG -- Debugger enable bit (bitmask:0x2000) | ||||
| DEBUG = ON | 0x1FFF | Background debugger enabled. | ||
| DEBUG = OFF | 0x3FFF | Background debugger disabled. | ||
| CONFIG3 (address:0x8009, mask:0x3F7F, default:0x3F7F) | ||||
| WDTCPS -- WDT Period Select bits (bitmask:0x001F) | ||||
| WDTCPS = WDTCPS_0 | 0x3FE0 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_1 | 0x3FE1 | Divider ratio 1:64. | ||
| WDTCPS = WDTCPS_2 | 0x3FE2 | Divider ratio 1:128. | ||
| WDTCPS = WDTCPS_3 | 0x3FE3 | Divider ratio 1:256. | ||
| WDTCPS = WDTCPS_4 | 0x3FE4 | Divider ratio 1:512. | ||
| WDTCPS = WDTCPS_5 | 0x3FE5 | Divider ratio 1:1024. | ||
| WDTCPS = WDTCPS_6 | 0x3FE6 | Divider ratio 1:2048. | ||
| WDTCPS = WDTCPS_7 | 0x3FE7 | Divider ratio 1:4096. | ||
| WDTCPS = WDTCPS_8 | 0x3FE8 | Divider ratio 1:8192. | ||
| WDTCPS = WDTCPS_9 | 0x3FE9 | Divider ratio 1:16384. | ||
| WDTCPS = WDTCPS_10 | 0x3FEA | Divider ratio 1:32768. | ||
| WDTCPS = WDTCPS_11 | 0x3FEB | Divider ratio 1:65536. | ||
| WDTCPS = WDTCPS_12 | 0x3FEC | Divider ratio 1:131072. | ||
| WDTCPS = WDTCPS_13 | 0x3FED | Divider ratio 1:262144. | ||
| WDTCPS = WDTCPS_14 | 0x3FEE | Divider ratio 1:524299. | ||
| WDTCPS = WDTCPS_15 | 0x3FEF | Divider ratio 1:1048576. | ||
| WDTCPS = WDTCPS_16 | 0x3FF0 | Divider ratio 1:2097152. | ||
| WDTCPS = WDTCPS_17 | 0x3FF1 | Divider ratio 1:4194304. | ||
| WDTCPS = WDTCPS_18 | 0x3FF2 | Divider ratio 1:8388608. | ||
| WDTCPS = WDTCPS_19 | 0x3FF3 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_20 | 0x3FF4 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_21 | 0x3FF5 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_22 | 0x3FF6 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_23 | 0x3FF7 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_24 | 0x3FF8 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_25 | 0x3FF9 | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_26 | 0x3FFA | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_27 | 0x3FFB | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_28 | 0x3FFC | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_29 | 0x3FFD | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_30 | 0x3FFE | Divider ratio 1:32. | ||
| WDTCPS = WDTCPS_31 | 0x3FFF | Divider ratio 1:65536; software control of WDTPS. | ||
| WDTE -- WDT operating mode (bitmask:0x0060) | ||||
| WDTE = OFF | 0x3F9F | WDT Disabled, SWDTEN is ignored. | ||
| WDTE = SWDTEN | 0x3FBF | WDT enabled/disabled by SWDTEN bit in WDTCON0. | ||
| WDTE = NSLEEP | 0x3FDF | WDT enabled while sleep=0, suspended when sleep=1; SWDTEN ignored. | ||
| WDTE = ON | 0x3FFF | WDT enabled regardless of sleep; SWDTEN ignored. | ||
| WDTCWS -- WDT Window Select bits (bitmask:0x0700) | ||||
| WDTCWS = WDTCWS_0 | 0x38FF | window delay = 87.5 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_1 | 0x39FF | window delay = 75 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_2 | 0x3AFF | window delay = 62.5 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_3 | 0x3BFF | window delay = 50 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_4 | 0x3CFF | window delay = 37.5 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_5 | 0x3DFF | window delay = 25 percent of time; no software control; keyed access required. | ||
| WDTCWS = WDTCWS_6 | 0x3EFF | window always open (100%); no software control; keyed access required. | ||
| WDTCWS = WDTCWS_7 | 0x3FFF | window always open (100%); software control; keyed access not required. | ||
| WDTCCS -- WDT input clock selector (bitmask:0x3800) | ||||
| WDTCCS = LFINTOSC | 0x07FF | WDT reference clock is the 31.0kHz LFINTOSC output. | ||
| WDTCCS = HFINTOSC | 0x0FFF | WDT reference clock is the 31.25 kHz HFINTOSC. | ||
| WDTCCS = SC | 0x3FFF | Software Control. | ||
| CONFIG4 (address:0x800A, mask:0x2F9F, default:0x2F9F) | ||||
| BBSIZE -- Boot Block Size Selection bits (bitmask:0x0007) | ||||
| BBSIZE = 65536 | 0x3FF8 | Boot Block Size (Words) 65536. | ||
| BBSIZE = 32768 | 0x3FF9 | Boot Block Size (Words) 32768. | ||
| BBSIZE = 16384 | 0x3FFA | Boot Block Size (Words) 16384. | ||
| BBSIZE = 8192 | 0x3FFB | Boot Block Size (Words) 8192. | ||
| BBSIZE = 4096 | 0x3FFC | Boot Block Size (Words) 4069. | ||
| BBSIZE = 2048 | 0x3FFD | Boot Block Size (Words) 2048. | ||
| BBSIZE = 1024 | 0x3FFE | Boot Block Size (Words) 1024. | ||
| BBSIZE = 512 | 0x3FFF | Boot Block Size (Words) 512. | ||
| BBEN -- Boot Block Enable bit (bitmask:0x0008) | ||||
| BBEN = ON | 0x3FF7 | Boot Block enabled. | ||
| BBEN = OFF | 0x3FFF | Boot Block disabled. | ||
| SAFEN -- SAF Enable bit (bitmask:0x0010) | ||||
| SAFEN = ON | 0x3FEF | SAF enabled. | ||
| SAFEN = OFF | 0x3FFF | SAF disabled. | ||
| WRTAPP -- Application Block Write Protection bit (bitmask:0x0080) | ||||
| WRTAPP = ON | 0x3F7F | Application Block write-protected. | ||
| WRTAPP = OFF | 0x3FFF | Application Block NOT write-protected. | ||
| WRTB -- Boot Block Write Protection bit (bitmask:0x0100) | ||||
| WRTB = ON | 0x3EFF | Boot Block write-protected. | ||
| WRTB = OFF | 0x3FFF | Boot Block NOT write-protected. | ||
| WRTC -- Configuration Register Write Protection bit (bitmask:0x0200) | ||||
| WRTC = ON | 0x3DFF | Configuration Word write-protected. | ||
| WRTC = OFF | 0x3FFF | Configuration Words NOT write-protected. | ||
| WRTD -- Data EEPROM Write Protection bit (bitmask:0x0400) | ||||
| WRTD = ON | 0x3BFF | Data EEPROM write-protected. | ||
| WRTD = OFF | 0x3FFF | Data EEPROM NOT write-protected. | ||
| WRTSAF -- Storage Area Flash Write Protection bit (bitmask:0x0800) | ||||
| WRTSAF = ON | 0x37FF | SAF write-protected. | ||
| WRTSAF = OFF | 0x3FFF | SAF NOT write-protected. | ||
| LVP -- Low Voltage Programming Enable bit (bitmask:0x2000) | ||||
| LVP = OFF | 0x1FFF | High Voltage on MCLR/Vpp must be used for programming. | ||
| LVP = ON | 0x3FFF | Low Voltage programming enabled. MCLR/Vpp pin function is MCLR. | ||
| CONFIG5 (address:0x800B, mask:0x0001, default:0x0001) | ||||
| CP -- UserNVM Program memory code protection bit (bitmask:0x0001) | ||||
| CP = ON | 0x3FFE | UserNVM code protection enabled. | ||
| CP = OFF | 0x3FFF | UserNVM code protection disabled. | ||
This page generated automatically by the device-help.pl program (2017-05-13 09:29:47 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.