| PIC16LF18313 | ||||
|---|---|---|---|---|
| CONFIG1 (address:0x8007, mask:0x2977, default:0x2977) | ||||
| FEXTOSC -- FEXTOSC External Oscillator mode Selection bits (bitmask:0x0007) | ||||
| FEXTOSC = LP | 0x3FF8 | LP (crystal oscillator) optimized for 32.768 kHz. | ||
| FEXTOSC = XT | 0x3FF9 | XT (crystal oscillator) from 100 kHz to 4 MHz. | ||
| FEXTOSC = HS | 0x3FFA | HS (crystal oscillator) above 4 MHz. | ||
| FEXTOSC = OFF | 0x3FFC | Oscillator not enabled. | ||
| FEXTOSC = ECL | 0x3FFD | EC (external clock) below 100 kHz. | ||
| FEXTOSC = ECM | 0x3FFE | EC (external clock) for 100 kHz to 8 MHz. | ||
| FEXTOSC = ECH | 0x3FFF | EC (external clock) above 8 MHz. | ||
| RSTOSC -- Power-up default value for COSC bits (bitmask:0x0070) | ||||
| RSTOSC = HFINT32 | 0x3F8F | HFINTOSC with 2x PLL (32MHz). | ||
| RSTOSC = EXT4X | 0x3F9F | EXTOSC with 4x PLL, with EXTOSC operating per FEXTOSC bits. | ||
| RSTOSC = SOSC | 0x3FBF | SOSC (31kHz). | ||
| RSTOSC = LFINT | 0x3FCF | LFINTOSC (31kHz). | ||
| RSTOSC = HFINT1 | 0x3FEF | HFINTOSC (1MHz). | ||
| RSTOSC = EXT1X | 0x3FFF | EXTOSC operating per FEXTOSC bits. | ||
| CLKOUTEN -- Clock Out Enable bit (bitmask:0x0100) | ||||
| CLKOUTEN = ON | 0x3EFF | CLKOUT function is enabled; FOSC/4 clock appears at OSC2. | ||
| CLKOUTEN = OFF | 0x3FFF | CLKOUT function is disabled; I/O or oscillator function on OSC2. | ||
| CSWEN -- Clock Switch Enable bit (bitmask:0x0800) | ||||
| CSWEN = OFF | 0x37FF | The NOSC and NDIV bits cannot be changed by user software. | ||
| CSWEN = ON | 0x3FFF | Writing to NOSC and NDIV is allowed. | ||
| FCMEN -- Fail-Safe Clock Monitor Enable (bitmask:0x2000) | ||||
| FCMEN = OFF | 0x1FFF | Fail-Safe Clock Monitor is disabled. | ||
| FCMEN = ON | 0x3FFF | Fail-Safe Clock Monitor is enabled. | ||
| CONFIG2 (address:0x8008, mask:0x3AEF, default:0x3AEF) | ||||
| MCLRE -- Master Clear Enable bit (bitmask:0x0001) | ||||
| MCLRE = OFF | 0x3FFE | MCLR/VPP pin function is digital input; MCLR internally disabled; Weak pull-up under control of port pin's WPU control bit. | ||
| MCLRE = ON | 0x3FFF | MCLR/VPP pin function is MCLR; Weak pull-up enabled . | ||
| PWRTE -- Power-up Timer Enable bit (bitmask:0x0002) | ||||
| PWRTE = ON | 0x3FFD | PWRT enabled. | ||
| PWRTE = OFF | 0x3FFF | PWRT disabled. | ||
| WDTE -- Watchdog Timer Enable bits (bitmask:0x000C) | ||||
| WDTE = OFF | 0x3FF3 | WDT disabled; SWDTEN is ignored. | ||
| WDTE = SWDTEN | 0x3FF7 | WDT controlled by the SWDTEN bit in the WDTCON register. | ||
| WDTE = SLEEP | 0x3FFB | WDT enabled while running and disabled while in SLEEP/IDLE; SWDTEN is ignored. | ||
| WDTE = ON | 0x3FFF | WDT enabled, SWDTEN is ignored. | ||
| LPBOREN -- Low-power BOR enable bit (bitmask:0x0020) | ||||
| LPBOREN = ON | 0x3FDF | ULPBOR enabled. | ||
| LPBOREN = OFF | 0x3FFF | ULPBOR disabled. | ||
| BOREN -- Brown-out Reset Enable bits (bitmask:0x00C0) | ||||
| BOREN = OFF | 0x3F3F | Brown-out Reset disabled. | ||
| BOREN = SBOREN | 0x3F7F | Brown-out Reset enabled according to SBOREN. | ||
| BOREN = SLEEP | 0x3FBF | Brown-out Reset enabled while running, disabled in Sleep; SBOREN is ignored. | ||
| BOREN = ON | 0x3FFF | Brown-out Reset enabled, SBOREN bit ignored. | ||
| BORV -- Brown-out Reset Voltage selection bit (bitmask:0x0200) | ||||
| BORV = HIGH | 0x3DFF | Brown-out voltage (Vbor) set to 2.7V. | ||
| BORV = LOW | 0x3FFF | Brown-out voltage (Vbor) set to 2.45V. | ||
| PPS1WAY -- PPSLOCK bit One-Way Set Enable bit (bitmask:0x0800) | ||||
| PPS1WAY = OFF | 0x37FF | The PPSLOCK bit can be set and cleared repeatedly (subject to the unlock sequence). | ||
| PPS1WAY = ON | 0x3FFF | The PPSLOCK bit can be cleared and set only once; PPS registers remain locked after one clear/set cycle. | ||
| STVREN -- Stack Overflow/Underflow Reset Enable bit (bitmask:0x1000) | ||||
| STVREN = OFF | 0x2FFF | Stack Overflow or Underflow will not cause a Reset. | ||
| STVREN = ON | 0x3FFF | Stack Overflow or Underflow will cause a Reset. | ||
| DEBUG -- Debugger enable bit (bitmask:0x2000) | ||||
| DEBUG = ON | 0x1FFF | Background debugger enabled. | ||
| DEBUG = OFF | 0x3FFF | Background debugger disabled. | ||
| CONFIG3 (address:0x8009, mask:0x2003, default:0x2003) | ||||
| WRT -- User NVM self-write protection bits (bitmask:0x0003) | ||||
| WRT = ALL | 0x3FFC | 0000h to 07FFh write protected, no addresses may be modified. | ||
| WRT = HALF | 0x3FFD | 0000h to 03FFh write-protected, 0400h to 07FFh may be modified. | ||
| WRT = BOOT | 0x3FFE | 0000h to 01FFh write-protected, 0200h to 07FFh may be modified. | ||
| WRT = OFF | 0x3FFF | Write protection off. | ||
| LVP -- Low Voltage Programming Enable bit (bitmask:0x2000) | ||||
| LVP = OFF | 0x1FFF | HV on MCLR/VPP must be used for programming. | ||
| LVP = ON | 0x3FFF | Low voltage programming enabled. MCLR/VPP pin function is MCLR. MCLRE configuration bit is ignored. | ||
| CONFIG4 (address:0x800A, mask:0x0003, default:0x0003) | ||||
| CP -- User NVM Program Memory Code Protection bit (bitmask:0x0001) | ||||
| CP = ON | 0x3FFE | User NVM code protection enabled. | ||
| CP = OFF | 0x3FFF | User NVM code protection disabled. | ||
| CPD -- Data NVM Memory Code Protection bit (bitmask:0x0002) | ||||
| CPD = ON | 0x3FFD | Data NVM code protection enabled. | ||
| CPD = OFF | 0x3FFF | Data NVM code protection disabled. | ||
This page generated automatically by the device-help.pl program (2017-05-13 09:29:49 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.