| PIC16LF877A | ||||
|---|---|---|---|---|
| CONFIG (address:0x2007, mask:0x2FCF, default:0x2FCF) | ||||
| FOSC -- Oscillator Selection bits (bitmask:0x0003) | ||||
| FOSC = LP | 0x3FFC | LP oscillator. | ||
| FOSC = XT | 0x3FFD | XT oscillator. | ||
| FOSC = HS | 0x3FFE | HS oscillator. | ||
| FOSC = EXTRC | 0x3FFF | RC oscillator. | ||
| WDTE -- Watchdog Timer Enable bit (bitmask:0x0004) | ||||
| WDTE = OFF | 0x3FFB | WDT disabled. | ||
| WDTE = ON | 0x3FFF | WDT enabled. | ||
| PWRTE -- Power-up Timer Enable bit (bitmask:0x0008) | ||||
| PWRTE = ON | 0x3FF7 | PWRT enabled. | ||
| PWRTE = OFF | 0x3FFF | PWRT disabled. | ||
| BOREN -- Brown-out Reset Enable bit (bitmask:0x0040) | ||||
| BOREN = OFF | 0x3FBF | BOR disabled. | ||
| BOREN = ON | 0x3FFF | BOR enabled. | ||
| LVP -- Low-Voltage (Single-Supply) In-Circuit Serial Programming Enable bit (bitmask:0x0080) | ||||
| LVP = OFF | 0x3F7F | RB3 is digital I/O, HV on MCLR must be used for programming. | ||
| LVP = ON | 0x3FFF | RB3/PGM pin has PGM function; low-voltage programming enabled. | ||
| CPD -- Data EEPROM Memory Code Protection bit (bitmask:0x0100) | ||||
| CPD = ON | 0x3EFF | Data EEPROM code-protected. | ||
| CPD = OFF | 0x3FFF | Data EEPROM code protection off. | ||
| WRT -- Flash Program Memory Write Enable bits (bitmask:0x0600) | ||||
| WRT = HALF | 0x39FF | 0000h to 0FFFh write-protected; 1000h to 1FFFh may be written to by EECON control. | ||
| WRT = 1FOURTH | 0x3BFF | 0000h to 07FFh write-protected; 0800h to 1FFFh may be written to by EECON control. | ||
| WRT = 256 | 0x3DFF | 0000h to 00FFh write-protected; 0100h to 1FFFh may be written to by EECON control. | ||
| WRT = OFF | 0x3FFF | Write protection off; all program memory may be written to by EECON control. | ||
| DEBUG -- In-Circuit Debugger Mode bit (bitmask:0x0800) | ||||
| DEBUG = ON | 0x37FF | In-Circuit Debugger enabled, RB6 and RB7 are dedicated to the debugger. | ||
| DEBUG = OFF | 0x3FFF | In-Circuit Debugger disabled, RB6 and RB7 are general purpose I/O pins. | ||
| CP -- Flash Program Memory Code Protection bit (bitmask:0x2000) | ||||
| CP = ON | 0x1FFF | All program memory code-protected. | ||
| CP = OFF | 0x3FFF | Code protection off. | ||
This page generated automatically by the device-help.pl program (2017-05-13 09:29:47 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.