| PIC18C658 | ||||
|---|---|---|---|---|
| CONFIG1L (address:0x300000, mask:0xFF, default:0xFF) | ||||
| CP -- Code Protection bits (bitmask:0xFF) | ||||
| CP = ON | 0x00 | All of program memory code protected. | ||
| CP = OFF | 0xFF | Program memory code protection off. | ||
| CONFIG1H (address:0x300001, mask:0x27, default:0x27) | ||||
| OSC -- Oscillator Selection bits (bitmask:0x07) | ||||
| OSC = LP | 0xF8 | LP oscillator. | ||
| OSC = XT | 0xF9 | XT oscillator. | ||
| OSC = HS | 0xFA | HS oscillator. | ||
| OSC = RC | 0xFB | RC oscillator. | ||
| OSC = EC | 0xFC | EC oscillator w/ OSC2 configured as divide by 4 clock output. | ||
| OSC = ECIO | 0xFD | EC oscillator w/ OSC2 configured as RA6. | ||
| OSC = HSPLL | 0xFE | HS4 oscillator with PLL enabled/Clock frequency = (4 x Fosc). | ||
| OSC = RCIO | 0xFF | RC oscillator w/ OSC2 configured as RA6. | ||
| OSCS -- Oscillator System Clock Switch Enable bit (bitmask:0x20) | ||||
| OSCS = ON | 0xDF | Oscillator system clock switch option is enabled (Oscillator switching is enabled). | ||
| OSCS = OFF | 0xFF | Oscillator system clock switch option is disabled (Main oscillator is source). | ||
| CONFIG2L (address:0x300002, mask:0x0F, default:0x0F) | ||||
| PWRT -- Power-up Timer Enable bit (bitmask:0x01) | ||||
| PWRT = ON | 0xFE | PWRT enabled. | ||
| PWRT = OFF | 0xFF | PWRT disabled. | ||
| BOR -- Brown-out Reset Enable bit (bitmask:0x02) | ||||
| BOR = OFF | 0xFD | Brown-out Reset disabled. | ||
| BOR = ON | 0xFF | Brown-out Reset enabled. | ||
| BORV -- Brown-out Reset Voltage bits (bitmask:0x0C) | ||||
| BORV = 45 | 0xF3 | VBOR set to 4.5V. | ||
| BORV = 42 | 0xF7 | VBOR set to 4.2V. | ||
| BORV = 27 | 0xFB | VBOR set to 2.7V. | ||
| BORV = 25 | 0xFF | VBOR set to 2.5V. | ||
| CONFIG2H (address:0x300003, mask:0x0F, default:0x0F) | ||||
| WDT -- Watchdog Timer Enable bit (bitmask:0x01) | ||||
| WDT = OFF | 0xFE | WDT disabled (control is placed on the SWDTEN bit). | ||
| WDT = ON | 0xFF | WDT enabled. | ||
| WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x0E) | ||||
| WDTPS = 1 | 0xF1 | 1:1. | ||
| WDTPS = 2 | 0xF3 | 1:2. | ||
| WDTPS = 4 | 0xF5 | 1:4. | ||
| WDTPS = 8 | 0xF7 | 1:8. | ||
| WDTPS = 16 | 0xF9 | 1:16. | ||
| WDTPS = 32 | 0xFB | 1:32. | ||
| WDTPS = 64 | 0xFD | 1:64. | ||
| WDTPS = 128 | 0xFF | 1:128. | ||
| CONFIG4L (address:0x300006, mask:0x01, default:0x01) | ||||
| STVR -- Stack Full/Underflow RESET Enable bit (bitmask:0x01) | ||||
| STVR = OFF | 0xFE | Stack Full/Underflow will not cause RESET. | ||
| STVR = ON | 0xFF | Stack Full/Underflow will cause RESET. | ||
This page generated automatically by the device-help.pl program (2017-05-13 09:29:49 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.