PIC18F24K22

PIC18F24K22

CONFIG1H (address:0x300001, mask:0xFF, default:0x25)

FOSC -- Oscillator Selection bits (bitmask:0x0F)
FOSC = LP	0xF0	LP oscillator.
FOSC = XT	0xF1	XT oscillator.
FOSC = HSHP	0xF2	HS oscillator (high power > 16 MHz).
FOSC = HSMP	0xF3	HS oscillator (medium power 4-16 MHz).
FOSC = ECHP	0xF4	EC oscillator, CLKOUT function on OSC2 (high power, >16 MHz).
FOSC = ECHPIO6	0xF5	EC oscillator (high power, >16 MHz).
FOSC = RC	0xF6	External RC oscillator, CLKOUT function on OSC2.
FOSC = RCIO6	0xF7	External RC oscillator.
FOSC = INTIO67	0xF8	Internal oscillator block.
FOSC = INTIO7	0xF9	Internal oscillator block, CLKOUT function on OSC2.
FOSC = ECMP	0xFA	EC oscillator, CLKOUT function on OSC2 (medium power, 500 kHz-16 MHz).
FOSC = ECMPIO6	0xFB	EC oscillator (medium power, 500 kHz-16 MHz).
FOSC = ECLP	0xFC	EC oscillator, CLKOUT function on OSC2 (low power, <500 kHz).
FOSC = ECLPIO6	0xFD	EC oscillator (low power, <500 kHz).

PLLCFG -- 4X PLL Enable (bitmask:0x10)
PLLCFG = OFF	0xEF	Oscillator used directly.
PLLCFG = ON	0xFF	Oscillator multiplied by 4.

PRICLKEN -- Primary clock enable bit (bitmask:0x20)
PRICLKEN = OFF	0xDF	Primary clock can be disabled by software.
PRICLKEN = ON	0xFF	Primary clock enabled.

FCMEN -- Fail-Safe Clock Monitor Enable bit (bitmask:0x40)
FCMEN = OFF	0xBF	Fail-Safe Clock Monitor disabled.
FCMEN = ON	0xFF	Fail-Safe Clock Monitor enabled.

IESO -- Internal/External Oscillator Switchover bit (bitmask:0x80)
IESO = OFF	0x7F	Oscillator Switchover mode disabled.
IESO = ON	0xFF	Oscillator Switchover mode enabled.

CONFIG2L (address:0x300002, mask:0x1F, default:0x1F)

PWRTEN -- Power-up Timer Enable bit (bitmask:0x01)
PWRTEN = ON	0xFE	Power up timer enabled.
PWRTEN = OFF	0xFF	Power up timer disabled.

BOREN -- Brown-out Reset Enable bits (bitmask:0x06)
BOREN = OFF	0xF9	Brown-out Reset disabled in hardware and software.
BOREN = ON	0xFB	Brown-out Reset enabled and controlled by software (SBOREN is enabled).
BOREN = NOSLP	0xFD	Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled).
BOREN = SBORDIS	0xFF	Brown-out Reset enabled in hardware only (SBOREN is disabled).

BORV -- Brown Out Reset Voltage bits (bitmask:0x18)
BORV = 285	0xE7	VBOR set to 2.85 V nominal.
BORV = 250	0xEF	VBOR set to 2.50 V nominal.
BORV = 220	0xF7	VBOR set to 2.20 V nominal.
BORV = 190	0xFF	VBOR set to 1.90 V nominal.

CONFIG2H (address:0x300003, mask:0x3F, default:0x3F)

WDTEN -- Watchdog Timer Enable bits (bitmask:0x03)
WDTEN = OFF	0xFC	Watch dog timer is always disabled. SWDTEN has no effect.
WDTEN = NOSLP	0xFD	WDT is disabled in sleep, otherwise enabled. SWDTEN bit has no effect.
WDTEN = SWON	0xFE	WDT is controlled by SWDTEN bit of the WDTCON register.
WDTEN = ON	0xFF	WDT is always enabled. SWDTEN bit has no effect.

WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x3C)
WDTPS = 1	0xC3	1:1.
WDTPS = 2	0xC7	1:2.
WDTPS = 4	0xCB	1:4.
WDTPS = 8	0xCF	1:8.
WDTPS = 16	0xD3	1:16.
WDTPS = 32	0xD7	1:32.
WDTPS = 64	0xDB	1:64.
WDTPS = 128	0xDF	1:128.
WDTPS = 256	0xE3	1:256.
WDTPS = 512	0xE7	1:512.
WDTPS = 1024	0xEB	1:1024.
WDTPS = 2048	0xEF	1:2048.
WDTPS = 4096	0xF3	1:4096.
WDTPS = 8192	0xF7	1:8192.
WDTPS = 16384	0xFB	1:16384.
WDTPS = 32768	0xFF	1:32768.

CONFIG3H (address:0x300005, mask:0xBF, default:0xBF)

CCP2MX -- CCP2 MUX bit (bitmask:0x01)
CCP2MX = PORTB3	0xFE	CCP2 input/output is multiplexed with RB3.
CCP2MX = PORTC1	0xFF	CCP2 input/output is multiplexed with RC1.

PBADEN -- PORTB A/D Enable bit (bitmask:0x02)
PBADEN = OFF	0xFD	PORTB<5:0> pins are configured as digital I/O on Reset.
PBADEN = ON	0xFF	PORTB<5:0> pins are configured as analog input channels on Reset.

CCP3MX -- P3A/CCP3 Mux bit (bitmask:0x04)
CCP3MX = PORTC6	0xFB	P3A/CCP3 input/output is mulitplexed with RC6.
CCP3MX = PORTB5	0xFF	P3A/CCP3 input/output is multiplexed with RB5.

HFOFST -- HFINTOSC Fast Start-up (bitmask:0x08)
HFOFST = OFF	0xF7	HFINTOSC output and ready status are delayed by the oscillator stable status.
HFOFST = ON	0xFF	HFINTOSC output and ready status are not delayed by the oscillator stable status.

T3CMX -- Timer3 Clock input mux bit (bitmask:0x10)
T3CMX = PORTB5	0xEF	T3CKI is on RB5.
T3CMX = PORTC0	0xFF	T3CKI is on RC0.

P2BMX -- ECCP2 B output mux bit (bitmask:0x20)
P2BMX = PORTC0	0xDF	P2B is on RC0.
P2BMX = PORTB5	0xFF	P2B is on RB5.

MCLRE -- MCLR Pin Enable bit (bitmask:0x80)
MCLRE = INTMCLR	0x7F	RE3 input pin enabled; MCLR disabled.
MCLRE = EXTMCLR	0xFF	MCLR pin enabled, RE3 input pin disabled.

CONFIG4L (address:0x300006, mask:0xC5, default:0x85)

STVREN -- Stack Full/Underflow Reset Enable bit (bitmask:0x01)
STVREN = OFF	0xFE	Stack full/underflow will not cause Reset.
STVREN = ON	0xFF	Stack full/underflow will cause Reset.

LVP -- Single-Supply ICSP Enable bit (bitmask:0x04)
LVP = OFF	0xFB	Single-Supply ICSP disabled.
LVP = ON	0xFF	Single-Supply ICSP enabled if MCLRE is also 1.

XINST -- Extended Instruction Set Enable bit (bitmask:0x40)
XINST = OFF	0xBF	Instruction set extension and Indexed Addressing mode disabled (Legacy mode).
XINST = ON	0xFF	Instruction set extension and Indexed Addressing mode enabled.

DEBUG -- Background Debug (bitmask:0x80)
DEBUG = ON	0x7F	Enabled.
DEBUG = OFF	0xFF	Disabled.

CONFIG5L (address:0x300008, mask:0x03, default:0x03)

CP0 -- Code Protection Block 0 (bitmask:0x01)
CP0 = ON	0xFE	Block 0 (000800-001FFFh) code-protected.
CP0 = OFF	0xFF	Block 0 (000800-001FFFh) not code-protected.

CP1 -- Code Protection Block 1 (bitmask:0x02)
CP1 = ON	0xFD	Block 1 (002000-003FFFh) code-protected.
CP1 = OFF	0xFF	Block 1 (002000-003FFFh) not code-protected.

CONFIG5H (address:0x300009, mask:0xC0, default:0xC0)

CPB -- Boot Block Code Protection bit (bitmask:0x40)
CPB = ON	0xBF	Boot block (000000-0007FFh) code-protected.
CPB = OFF	0xFF	Boot block (000000-0007FFh) not code-protected.

CPD -- Data EEPROM Code Protection bit (bitmask:0x80)
CPD = ON	0x7F	Data EEPROM code-protected.
CPD = OFF	0xFF	Data EEPROM not code-protected.

CONFIG6L (address:0x30000A, mask:0x03, default:0x03)

WRT0 -- Write Protection Block 0 (bitmask:0x01)
WRT0 = ON	0xFE	Block 0 (000800-001FFFh) write-protected.
WRT0 = OFF	0xFF	Block 0 (000800-001FFFh) not write-protected.

WRT1 -- Write Protection Block 1 (bitmask:0x02)
WRT1 = ON	0xFD	Block 1 (002000-003FFFh) write-protected.
WRT1 = OFF	0xFF	Block 1 (002000-003FFFh) not write-protected.

CONFIG6H (address:0x30000B, mask:0xE0, default:0xE0)

WRTC -- Configuration Register Write Protection bit (bitmask:0x20)
WRTC = ON	0xDF	Configuration registers (300000-3000FFh) write-protected.
WRTC = OFF	0xFF	Configuration registers (300000-3000FFh) not write-protected.

WRTB -- Boot Block Write Protection bit (bitmask:0x40)
WRTB = ON	0xBF	Boot Block (000000-0007FFh) write-protected.
WRTB = OFF	0xFF	Boot Block (000000-0007FFh) not write-protected.

WRTD -- Data EEPROM Write Protection bit (bitmask:0x80)
WRTD = ON	0x7F	Data EEPROM write-protected.
WRTD = OFF	0xFF	Data EEPROM not write-protected.

CONFIG7L (address:0x30000C, mask:0x03, default:0x03)

EBTR0 -- Table Read Protection Block 0 (bitmask:0x01)
EBTR0 = ON	0xFE	Block 0 (000800-001FFFh) protected from table reads executed in other blocks.
EBTR0 = OFF	0xFF	Block 0 (000800-001FFFh) not protected from table reads executed in other blocks.

EBTR1 -- Table Read Protection Block 1 (bitmask:0x02)
EBTR1 = ON	0xFD	Block 1 (002000-003FFFh) protected from table reads executed in other blocks.
EBTR1 = OFF	0xFF	Block 1 (002000-003FFFh) not protected from table reads executed in other blocks.

CONFIG7H (address:0x30000D, mask:0x40, default:0x40)

EBTRB -- Boot Block Table Read Protection bit (bitmask:0x40)
EBTRB = ON	0xBF	Boot Block (000000-0007FFh) protected from table reads executed in other blocks.
EBTRB = OFF	0xFF	Boot Block (000000-0007FFh) not protected from table reads executed in other blocks.

CONFIG1H (address:0x300001, mask:0xFF, default:0x25)

FOSC -- Oscillator Selection bits (bitmask:0x0F)

FOSC = LP

0xF0

LP oscillator.

FOSC = XT

0xF1

XT oscillator.

FOSC = HSHP

0xF2

HS oscillator (high power > 16 MHz).

FOSC = HSMP

0xF3

HS oscillator (medium power 4-16 MHz).

FOSC = ECHP

0xF4

EC oscillator, CLKOUT function on OSC2 (high power, >16 MHz).

FOSC = ECHPIO6

0xF5

EC oscillator (high power, >16 MHz).

FOSC = RC

0xF6

External RC oscillator, CLKOUT function on OSC2.

FOSC = RCIO6

0xF7

External RC oscillator.

FOSC = INTIO67

0xF8

Internal oscillator block.

FOSC = INTIO7

0xF9

Internal oscillator block, CLKOUT function on OSC2.

FOSC = ECMP

0xFA

EC oscillator, CLKOUT function on OSC2 (medium power, 500 kHz-16 MHz).

FOSC = ECMPIO6

0xFB

EC oscillator (medium power, 500 kHz-16 MHz).

FOSC = ECLP

0xFC

EC oscillator, CLKOUT function on OSC2 (low power, <500 kHz).

FOSC = ECLPIO6

0xFD

EC oscillator (low power, <500 kHz).

PLLCFG -- 4X PLL Enable (bitmask:0x10)

PLLCFG = OFF

0xEF

Oscillator used directly.

PLLCFG = ON

0xFF

Oscillator multiplied by 4.

PRICLKEN -- Primary clock enable bit (bitmask:0x20)

PRICLKEN = OFF

0xDF

Primary clock can be disabled by software.

PRICLKEN = ON

0xFF

Primary clock enabled.

FCMEN -- Fail-Safe Clock Monitor Enable bit (bitmask:0x40)

FCMEN = OFF

0xBF

Fail-Safe Clock Monitor disabled.

FCMEN = ON

0xFF

Fail-Safe Clock Monitor enabled.

IESO -- Internal/External Oscillator Switchover bit (bitmask:0x80)

IESO = OFF

0x7F

Oscillator Switchover mode disabled.

IESO = ON

0xFF

Oscillator Switchover mode enabled.

CONFIG2L (address:0x300002, mask:0x1F, default:0x1F)

PWRTEN -- Power-up Timer Enable bit (bitmask:0x01)

PWRTEN = ON

0xFE

Power up timer enabled.

PWRTEN = OFF

0xFF

Power up timer disabled.

BOREN -- Brown-out Reset Enable bits (bitmask:0x06)

BOREN = OFF

0xF9

Brown-out Reset disabled in hardware and software.

BOREN = ON

0xFB

Brown-out Reset enabled and controlled by software (SBOREN is enabled).

BOREN = NOSLP

0xFD

Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled).

BOREN = SBORDIS

0xFF

Brown-out Reset enabled in hardware only (SBOREN is disabled).

BORV -- Brown Out Reset Voltage bits (bitmask:0x18)

BORV = 285

0xE7

VBOR set to 2.85 V nominal.

BORV = 250

0xEF

VBOR set to 2.50 V nominal.

BORV = 220

0xF7

VBOR set to 2.20 V nominal.

BORV = 190

0xFF

VBOR set to 1.90 V nominal.

CONFIG2H (address:0x300003, mask:0x3F, default:0x3F)

WDTEN -- Watchdog Timer Enable bits (bitmask:0x03)

WDTEN = OFF

0xFC

Watch dog timer is always disabled. SWDTEN has no effect.

WDTEN = NOSLP

0xFD

WDT is disabled in sleep, otherwise enabled. SWDTEN bit has no effect.

WDTEN = SWON

0xFE

WDT is controlled by SWDTEN bit of the WDTCON register.

WDTEN = ON

0xFF

WDT is always enabled. SWDTEN bit has no effect.

WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x3C)

WDTPS = 1

0xC3

1:1.

WDTPS = 2

0xC7

1:2.

WDTPS = 4

0xCB

1:4.

WDTPS = 8

0xCF

1:8.

WDTPS = 16

0xD3

1:16.

WDTPS = 32

0xD7

1:32.

WDTPS = 64

0xDB

1:64.

WDTPS = 128

0xDF

1:128.

WDTPS = 256

0xE3

1:256.

WDTPS = 512

0xE7

1:512.

WDTPS = 1024

0xEB

1:1024.

WDTPS = 2048

0xEF

1:2048.

WDTPS = 4096

0xF3

1:4096.

WDTPS = 8192

0xF7

1:8192.

WDTPS = 16384

0xFB

1:16384.

WDTPS = 32768

0xFF

1:32768.

CONFIG3H (address:0x300005, mask:0xBF, default:0xBF)

CCP2MX -- CCP2 MUX bit (bitmask:0x01)

CCP2MX = PORTB3

0xFE

CCP2 input/output is multiplexed with RB3.

CCP2MX = PORTC1

0xFF

CCP2 input/output is multiplexed with RC1.

PBADEN -- PORTB A/D Enable bit (bitmask:0x02)

PBADEN = OFF

0xFD

PORTB<5:0> pins are configured as digital I/O on Reset.

PBADEN = ON

0xFF

PORTB<5:0> pins are configured as analog input channels on Reset.

CCP3MX -- P3A/CCP3 Mux bit (bitmask:0x04)

CCP3MX = PORTC6

0xFB

P3A/CCP3 input/output is mulitplexed with RC6.

CCP3MX = PORTB5

0xFF

P3A/CCP3 input/output is multiplexed with RB5.

HFOFST -- HFINTOSC Fast Start-up (bitmask:0x08)

HFOFST = OFF

0xF7

HFINTOSC output and ready status are delayed by the oscillator stable status.

HFOFST = ON

0xFF

HFINTOSC output and ready status are not delayed by the oscillator stable status.

T3CMX -- Timer3 Clock input mux bit (bitmask:0x10)

T3CMX = PORTB5

0xEF

T3CKI is on RB5.

T3CMX = PORTC0

0xFF

T3CKI is on RC0.

P2BMX -- ECCP2 B output mux bit (bitmask:0x20)

P2BMX = PORTC0

0xDF

P2B is on RC0.

P2BMX = PORTB5

0xFF

P2B is on RB5.

MCLRE -- MCLR Pin Enable bit (bitmask:0x80)

MCLRE = INTMCLR

0x7F

RE3 input pin enabled; MCLR disabled.

MCLRE = EXTMCLR

0xFF

MCLR pin enabled, RE3 input pin disabled.

CONFIG4L (address:0x300006, mask:0xC5, default:0x85)

STVREN -- Stack Full/Underflow Reset Enable bit (bitmask:0x01)

STVREN = OFF

0xFE

Stack full/underflow will not cause Reset.

STVREN = ON

0xFF

Stack full/underflow will cause Reset.

LVP -- Single-Supply ICSP Enable bit (bitmask:0x04)

LVP = OFF

0xFB

Single-Supply ICSP disabled.

LVP = ON

0xFF

Single-Supply ICSP enabled if MCLRE is also 1.

XINST -- Extended Instruction Set Enable bit (bitmask:0x40)

XINST = OFF

0xBF

Instruction set extension and Indexed Addressing mode disabled (Legacy mode).

XINST = ON

0xFF

Instruction set extension and Indexed Addressing mode enabled.

DEBUG -- Background Debug (bitmask:0x80)

DEBUG = ON

0x7F

Enabled.

DEBUG = OFF

0xFF

Disabled.

CONFIG5L (address:0x300008, mask:0x03, default:0x03)

CP0 -- Code Protection Block 0 (bitmask:0x01)

CP0 = ON

0xFE

Block 0 (000800-001FFFh) code-protected.

CP0 = OFF

0xFF

Block 0 (000800-001FFFh) not code-protected.

CP1 -- Code Protection Block 1 (bitmask:0x02)

CP1 = ON

0xFD

Block 1 (002000-003FFFh) code-protected.

CP1 = OFF

0xFF

Block 1 (002000-003FFFh) not code-protected.

CONFIG5H (address:0x300009, mask:0xC0, default:0xC0)

CPB -- Boot Block Code Protection bit (bitmask:0x40)

CPB = ON

0xBF

Boot block (000000-0007FFh) code-protected.

CPB = OFF

0xFF

Boot block (000000-0007FFh) not code-protected.

CPD -- Data EEPROM Code Protection bit (bitmask:0x80)

CPD = ON

0x7F

Data EEPROM code-protected.

CPD = OFF

0xFF

Data EEPROM not code-protected.

CONFIG6L (address:0x30000A, mask:0x03, default:0x03)

WRT0 -- Write Protection Block 0 (bitmask:0x01)

WRT0 = ON

0xFE

Block 0 (000800-001FFFh) write-protected.

WRT0 = OFF

0xFF

Block 0 (000800-001FFFh) not write-protected.

WRT1 -- Write Protection Block 1 (bitmask:0x02)

WRT1 = ON

0xFD

Block 1 (002000-003FFFh) write-protected.

WRT1 = OFF

0xFF

Block 1 (002000-003FFFh) not write-protected.

CONFIG6H (address:0x30000B, mask:0xE0, default:0xE0)

WRTC -- Configuration Register Write Protection bit (bitmask:0x20)

WRTC = ON

0xDF

Configuration registers (300000-3000FFh) write-protected.

WRTC = OFF

0xFF

Configuration registers (300000-3000FFh) not write-protected.

WRTB -- Boot Block Write Protection bit (bitmask:0x40)

WRTB = ON

0xBF

Boot Block (000000-0007FFh) write-protected.

WRTB = OFF

0xFF

Boot Block (000000-0007FFh) not write-protected.

WRTD -- Data EEPROM Write Protection bit (bitmask:0x80)

WRTD = ON

0x7F

Data EEPROM write-protected.

WRTD = OFF

0xFF

Data EEPROM not write-protected.

CONFIG7L (address:0x30000C, mask:0x03, default:0x03)

EBTR0 -- Table Read Protection Block 0 (bitmask:0x01)

EBTR0 = ON

0xFE

Block 0 (000800-001FFFh) protected from table reads executed in other blocks.

EBTR0 = OFF

0xFF

Block 0 (000800-001FFFh) not protected from table reads executed in other blocks.

EBTR1 -- Table Read Protection Block 1 (bitmask:0x02)

EBTR1 = ON

0xFD

Block 1 (002000-003FFFh) protected from table reads executed in other blocks.

EBTR1 = OFF

0xFF

Block 1 (002000-003FFFh) not protected from table reads executed in other blocks.

CONFIG7H (address:0x30000D, mask:0x40, default:0x40)

EBTRB -- Boot Block Table Read Protection bit (bitmask:0x40)

EBTRB = ON

0xBF

Boot Block (000000-0007FFh) protected from table reads executed in other blocks.

EBTRB = OFF

0xFF

Boot Block (000000-0007FFh) not protected from table reads executed in other blocks.

This page generated automatically by the device-help.pl program (2017-05-13 09:29:49 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.