PIC18LF2320

PIC18LF2320

CONFIG1H (address:0x300001, mask:0xCF, default:0xCF)

OSC -- Oscillator Selection bits (bitmask:0x0F)
OSC = LP	0xF0	LP Oscillator.
OSC = XT	0xF1	XT Oscillator.
OSC = HS	0xF2	HS Oscillator.
OSC = EC	0xF4	EC oscillator, CLKO function on RA6.
OSC = ECIO	0xF5	EC oscillator, port function on RA6.
OSC = HSPLL	0xF6	HS oscillator, PLL enabled (clock frequency = 4 x FOSC1).
OSC = RCIO	0xF7	External RC oscillator, port function on RA6.
OSC = INTIO2	0xF8	Internal RC oscillator, port function on RA6 and port function on RA7.
OSC = INTIO1	0xF9	Internal RC oscillator, CLKO function on RA6 and port function on RA7.
OSC = RC	0xFC	External RC oscillator, CLKO function on RA6.

FSCM -- Fail-Safe Clock Monitor Enable bit (bitmask:0x40)
FSCM = OFF	0xBF	Fail-Safe Clock Monitor disabled.
FSCM = ON	0xFF	Fail-Safe Clock Monitor enabled.

IESO -- Internal/External Switchover bit (bitmask:0x80)
IESO = OFF	0x7F	Internal/External Switchover mode disabled.
IESO = ON	0xFF	Internal/External Switchover mode enabled.

CONFIG2L (address:0x300002, mask:0x0F, default:0x0F)

PWRT -- Power-up Timer enable bit (bitmask:0x01)
PWRT = ON	0xFE	PWRT enabled.
PWRT = OFF	0xFF	PWRT disabled.

BOR -- Brown-out Reset enable bit (bitmask:0x02)
BOR = OFF	0xFD	Brown-out Reset disabled.
BOR = ON	0xFF	Brown-out Reset enabled.

BORV -- Brown-out Reset Voltage bits (bitmask:0x0C)
BORV = 45	0xF3	VBOR set to 4.5V.
BORV = 42	0xF7	VBOR set to 4.2V.
BORV = 27	0xFB	VBOR set to 2.7V.
BORV = 20	0xFF	VBOR set to 2.0V.

CONFIG2H (address:0x300003, mask:0x1F, default:0x1F)

WDT -- Watchdog Timer Enable bit (bitmask:0x01)
WDT = OFF	0xFE	WDT disabled (control is placed on the SWDTEN bit).
WDT = ON	0xFF	WDT enabled.

WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x1E)
WDTPS = 1	0xE1	1:1.
WDTPS = 2	0xE3	1:2.
WDTPS = 4	0xE5	1:4.
WDTPS = 8	0xE7	1:8.
WDTPS = 16	0xE9	1:16.
WDTPS = 32	0xEB	1:32.
WDTPS = 64	0xED	1:64.
WDTPS = 128	0xEF	1:128.
WDTPS = 256	0xF1	1:256.
WDTPS = 512	0xF3	1:512.
WDTPS = 1024	0xF5	1:1024.
WDTPS = 2048	0xF7	1:2048.
WDTPS = 4096	0xF9	1:4096.
WDTPS = 8192	0xFB	1:8192.
WDTPS = 16384	0xFD	1:16384.
WDTPS = 32768	0xFF	1:32768.

CONFIG3H (address:0x300005, mask:0x83, default:0x83)

CCP2MX -- CCP2 MUX bit (bitmask:0x01)
CCP2MX = OFF	0xFE	CCP2 input/output is multiplexed with RB3.
CCP2MX = ON	0xFF	CCP2 input/output is multiplexed with RC1.

PBAD -- PORTB A/D Enable bit (bitmask:0x02)
PBAD = DIG	0xFD	PORTB<4:0> pins are configured as digital I/O on Reset.
PBAD = ANA	0xFF	PORTB<4:0> pins are configured as analog input channels on Reset.

MCLRE -- MCLR Pin Enable bit (bitmask:0x80)
MCLRE = OFF	0x7F	MCLR disabled; RE3 input is enabled in 40-pin devices only (PIC18F4X20).
MCLRE = ON	0xFF	MCLR pin enabled; RE3 input pin disabled.

CONFIG4L (address:0x300006, mask:0x85, default:0x85)

STVR -- Stack Full/Underflow Reset Enable bit (bitmask:0x01)
STVR = OFF	0xFE	Stack full/underflow will not cause Reset.
STVR = ON	0xFF	Stack full/underflow will cause Reset.

LVP -- Single-Supply ICSP Enable bit (bitmask:0x04)
LVP = OFF	0xFB	Single-Supply ICSP disabled.
LVP = ON	0xFF	Single-Supply ICSP enabled.

DEBUG -- Background Debugger Enable bit (bitmask:0x80)
DEBUG = ON	0x7F	Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug.
DEBUG = OFF	0xFF	Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins.

CONFIG5L (address:0x300008, mask:0x0F, default:0x0F)

CP0 -- Code Protection bit (bitmask:0x01)
CP0 = ON	0xFE	Block 0 (000200-0007FFh) code-protected.
CP0 = OFF	0xFF	Block 0 (000200-0007FFh) not code-protected.

CP1 -- Code Protection bit (bitmask:0x02)
CP1 = ON	0xFD	Block 1 (000800-000FFFh) code-protected.
CP1 = OFF	0xFF	Block 1 (000800-000FFFh) not code-protected.

CP2 -- Code Protection bit (bitmask:0x04)
CP2 = ON	0xFB	Block 2 (001000-0017FFh) code-protected.
CP2 = OFF	0xFF	Block 2 (001000-0017FFh) not code-protected.

CP3 -- Code Protection bit (bitmask:0x08)
CP3 = ON	0xF7	Block 3 (001800-001FFFh) code-protected.
CP3 = OFF	0xFF	Block 3 (001800-001FFFh) not code-protected.

CONFIG5H (address:0x300009, mask:0xC0, default:0xC0)

CPB -- Boot Block Code Protection bit (bitmask:0x40)
CPB = ON	0xBF	Boot block (000000-0001FFh) is code-protected.
CPB = OFF	0xFF	Boot block (000000-0001FFh) is not code-protected.

CPD -- Data EEPROM Code Protection bit (bitmask:0x80)
CPD = ON	0x7F	Data EEPROM is code-protected.
CPD = OFF	0xFF	Data EEPROM is not code-protected.

CONFIG6L (address:0x30000A, mask:0x0F, default:0x0F)

WRT0 -- Write Protection bit (bitmask:0x01)
WRT0 = ON	0xFE	Block 0 (000200-0007FFh) write-protected.
WRT0 = OFF	0xFF	Block 0 (000200-0007FFh) not write-protected.

WRT1 -- Write Protection bit (bitmask:0x02)
WRT1 = ON	0xFD	Block 1 (000800-000FFFh) write-protected.
WRT1 = OFF	0xFF	Block 1 (000800-000FFFh) not write-protected.

WRT2 -- Write Protection bit (bitmask:0x04)
WRT2 = ON	0xFB	Block 2 (001000-0017FFh) write-protected.
WRT2 = OFF	0xFF	Block 2 (001000-0017FFh) not write-protected.

WRT3 -- Write Protection bit (bitmask:0x08)
WRT3 = ON	0xF7	Block 3 (001800-001FFFh) write-protected.
WRT3 = OFF	0xFF	Block 3 (001800-001FFFh) not write-protected.

CONFIG6H (address:0x30000B, mask:0xE0, default:0xE0)

WRTC -- Configuration Register Write Protection bit (bitmask:0x20)
WRTC = ON	0xDF	Configuration registers (300000-3000FFh) are write-protected.
WRTC = OFF	0xFF	Configuration registers (300000-3000FFh) are not write-protected.

WRTB -- Boot Block Write Protection bit (bitmask:0x40)
WRTB = ON	0xBF	Boot block (000000-0001FFh) is write-protected.
WRTB = OFF	0xFF	Boot block (000000-0001FFh) is not write-protected.

WRTD -- Data EEPROM Write Protection bit (bitmask:0x80)
WRTD = ON	0x7F	Data EEPROM is write-protected.
WRTD = OFF	0xFF	Data EEPROM is not write-protected.

CONFIG7L (address:0x30000C, mask:0x0F, default:0x0F)

EBTR0 -- Table Read Protection bit (bitmask:0x01)
EBTR0 = ON	0xFE	Block 0 (000200-0007FFh) protected from table reads executed in other blocks.
EBTR0 = OFF	0xFF	Block 0 (000200-0007FFh) not protected from table reads executed in other blocks.

EBTR1 -- Table Read Protection bit (bitmask:0x02)
EBTR1 = ON	0xFD	Block 1 (000800-000FFFh) protected from table reads executed in other blocks.
EBTR1 = OFF	0xFF	Block 1 (000800-000FFFh) not protected from table reads executed in other blocks.

EBTR2 -- Table Read Protection bit (bitmask:0x04)
EBTR2 = ON	0xFB	Block 2 (001000-0017FFh) protected from table reads executed in other blocks.
EBTR2 = OFF	0xFF	Block 2 (001000-0017FFh) not protected from table reads executed in other blocks.

EBTR3 -- Table Read Protection bit (bitmask:0x08)
EBTR3 = ON	0xF7	Block 3 (001800-001FFFh) protected from table reads executed in other blocks.
EBTR3 = OFF	0xFF	Block 3 (001800-001FFFh) not protected from table reads executed in other blocks.

CONFIG7H (address:0x30000D, mask:0x40, default:0x40)

EBTRB -- Boot Block Table Read Protection bit (bitmask:0x40)
EBTRB = ON	0xBF	Boot block (000000-0001FFh) is protected from table reads executed in other blocks.
EBTRB = OFF	0xFF	Boot block (000000-0001FFh) is not protected from table reads executed in other blocks.

CONFIG1H (address:0x300001, mask:0xCF, default:0xCF)

OSC -- Oscillator Selection bits (bitmask:0x0F)

OSC = LP

0xF0

LP Oscillator.

OSC = XT

0xF1

XT Oscillator.

OSC = HS

0xF2

HS Oscillator.

OSC = EC

0xF4

EC oscillator, CLKO function on RA6.

OSC = ECIO

0xF5

EC oscillator, port function on RA6.

OSC = HSPLL

0xF6

HS oscillator, PLL enabled (clock frequency = 4 x FOSC1).

OSC = RCIO

0xF7

External RC oscillator, port function on RA6.

OSC = INTIO2

0xF8

Internal RC oscillator, port function on RA6 and port function on RA7.

OSC = INTIO1

0xF9

Internal RC oscillator, CLKO function on RA6 and port function on RA7.

OSC = RC

0xFC

External RC oscillator, CLKO function on RA6.

FSCM -- Fail-Safe Clock Monitor Enable bit (bitmask:0x40)

FSCM = OFF

0xBF

Fail-Safe Clock Monitor disabled.

FSCM = ON

0xFF

Fail-Safe Clock Monitor enabled.

IESO -- Internal/External Switchover bit (bitmask:0x80)

IESO = OFF

0x7F

Internal/External Switchover mode disabled.

IESO = ON

0xFF

Internal/External Switchover mode enabled.

CONFIG2L (address:0x300002, mask:0x0F, default:0x0F)

PWRT -- Power-up Timer enable bit (bitmask:0x01)

PWRT = ON

0xFE

PWRT enabled.

PWRT = OFF

0xFF

PWRT disabled.

BOR -- Brown-out Reset enable bit (bitmask:0x02)

BOR = OFF

0xFD

Brown-out Reset disabled.

BOR = ON

0xFF

Brown-out Reset enabled.

BORV -- Brown-out Reset Voltage bits (bitmask:0x0C)

BORV = 45

0xF3

VBOR set to 4.5V.

BORV = 42

0xF7

VBOR set to 4.2V.

BORV = 27

0xFB

VBOR set to 2.7V.

BORV = 20

0xFF

VBOR set to 2.0V.

CONFIG2H (address:0x300003, mask:0x1F, default:0x1F)

WDT -- Watchdog Timer Enable bit (bitmask:0x01)

WDT = OFF

0xFE

WDT disabled (control is placed on the SWDTEN bit).

WDT = ON

0xFF

WDT enabled.

WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x1E)

WDTPS = 1

0xE1

1:1.

WDTPS = 2

0xE3

1:2.

WDTPS = 4

0xE5

1:4.

WDTPS = 8

0xE7

1:8.

WDTPS = 16

0xE9

1:16.

WDTPS = 32

0xEB

1:32.

WDTPS = 64

0xED

1:64.

WDTPS = 128

0xEF

1:128.

WDTPS = 256

0xF1

1:256.

WDTPS = 512

0xF3

1:512.

WDTPS = 1024

0xF5

1:1024.

WDTPS = 2048

0xF7

1:2048.

WDTPS = 4096

0xF9

1:4096.

WDTPS = 8192

0xFB

1:8192.

WDTPS = 16384

0xFD

1:16384.

WDTPS = 32768

0xFF

1:32768.

CONFIG3H (address:0x300005, mask:0x83, default:0x83)

CCP2MX -- CCP2 MUX bit (bitmask:0x01)

CCP2MX = OFF

0xFE

CCP2 input/output is multiplexed with RB3.

CCP2MX = ON

0xFF

CCP2 input/output is multiplexed with RC1.

PBAD -- PORTB A/D Enable bit (bitmask:0x02)

PBAD = DIG

0xFD

PORTB<4:0> pins are configured as digital I/O on Reset.

PBAD = ANA

0xFF

PORTB<4:0> pins are configured as analog input channels on Reset.

MCLRE -- MCLR Pin Enable bit (bitmask:0x80)

MCLRE = OFF

0x7F

MCLR disabled; RE3 input is enabled in 40-pin devices only (PIC18F4X20).

MCLRE = ON

0xFF

MCLR pin enabled; RE3 input pin disabled.

CONFIG4L (address:0x300006, mask:0x85, default:0x85)

STVR -- Stack Full/Underflow Reset Enable bit (bitmask:0x01)

STVR = OFF

0xFE

Stack full/underflow will not cause Reset.

STVR = ON

0xFF

Stack full/underflow will cause Reset.

LVP -- Single-Supply ICSP Enable bit (bitmask:0x04)

LVP = OFF

0xFB

Single-Supply ICSP disabled.

LVP = ON

0xFF

Single-Supply ICSP enabled.

DEBUG -- Background Debugger Enable bit (bitmask:0x80)

DEBUG = ON

0x7F

Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug.

DEBUG = OFF

0xFF

Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins.

CONFIG5L (address:0x300008, mask:0x0F, default:0x0F)

CP0 -- Code Protection bit (bitmask:0x01)

CP0 = ON

0xFE

Block 0 (000200-0007FFh) code-protected.

CP0 = OFF

0xFF

Block 0 (000200-0007FFh) not code-protected.

CP1 -- Code Protection bit (bitmask:0x02)

CP1 = ON

0xFD

Block 1 (000800-000FFFh) code-protected.

CP1 = OFF

0xFF

Block 1 (000800-000FFFh) not code-protected.

CP2 -- Code Protection bit (bitmask:0x04)

CP2 = ON

0xFB

Block 2 (001000-0017FFh) code-protected.

CP2 = OFF

0xFF

Block 2 (001000-0017FFh) not code-protected.

CP3 -- Code Protection bit (bitmask:0x08)

CP3 = ON

0xF7

Block 3 (001800-001FFFh) code-protected.

CP3 = OFF

0xFF

Block 3 (001800-001FFFh) not code-protected.

CONFIG5H (address:0x300009, mask:0xC0, default:0xC0)

CPB -- Boot Block Code Protection bit (bitmask:0x40)

CPB = ON

0xBF

Boot block (000000-0001FFh) is code-protected.

CPB = OFF

0xFF

Boot block (000000-0001FFh) is not code-protected.

CPD -- Data EEPROM Code Protection bit (bitmask:0x80)

CPD = ON

0x7F

Data EEPROM is code-protected.

CPD = OFF

0xFF

Data EEPROM is not code-protected.

CONFIG6L (address:0x30000A, mask:0x0F, default:0x0F)

WRT0 -- Write Protection bit (bitmask:0x01)

WRT0 = ON

0xFE

Block 0 (000200-0007FFh) write-protected.

WRT0 = OFF

0xFF

Block 0 (000200-0007FFh) not write-protected.

WRT1 -- Write Protection bit (bitmask:0x02)

WRT1 = ON

0xFD

Block 1 (000800-000FFFh) write-protected.

WRT1 = OFF

0xFF

Block 1 (000800-000FFFh) not write-protected.

WRT2 -- Write Protection bit (bitmask:0x04)

WRT2 = ON

0xFB

Block 2 (001000-0017FFh) write-protected.

WRT2 = OFF

0xFF

Block 2 (001000-0017FFh) not write-protected.

WRT3 -- Write Protection bit (bitmask:0x08)

WRT3 = ON

0xF7

Block 3 (001800-001FFFh) write-protected.

WRT3 = OFF

0xFF

Block 3 (001800-001FFFh) not write-protected.

CONFIG6H (address:0x30000B, mask:0xE0, default:0xE0)

WRTC -- Configuration Register Write Protection bit (bitmask:0x20)

WRTC = ON

0xDF

Configuration registers (300000-3000FFh) are write-protected.

WRTC = OFF

0xFF

Configuration registers (300000-3000FFh) are not write-protected.

WRTB -- Boot Block Write Protection bit (bitmask:0x40)

WRTB = ON

0xBF

Boot block (000000-0001FFh) is write-protected.

WRTB = OFF

0xFF

Boot block (000000-0001FFh) is not write-protected.

WRTD -- Data EEPROM Write Protection bit (bitmask:0x80)

WRTD = ON

0x7F

Data EEPROM is write-protected.

WRTD = OFF

0xFF

Data EEPROM is not write-protected.

CONFIG7L (address:0x30000C, mask:0x0F, default:0x0F)

EBTR0 -- Table Read Protection bit (bitmask:0x01)

EBTR0 = ON

0xFE

Block 0 (000200-0007FFh) protected from table reads executed in other blocks.

EBTR0 = OFF

0xFF

Block 0 (000200-0007FFh) not protected from table reads executed in other blocks.

EBTR1 -- Table Read Protection bit (bitmask:0x02)

EBTR1 = ON

0xFD

Block 1 (000800-000FFFh) protected from table reads executed in other blocks.

EBTR1 = OFF

0xFF

Block 1 (000800-000FFFh) not protected from table reads executed in other blocks.

EBTR2 -- Table Read Protection bit (bitmask:0x04)

EBTR2 = ON

0xFB

Block 2 (001000-0017FFh) protected from table reads executed in other blocks.

EBTR2 = OFF

0xFF

Block 2 (001000-0017FFh) not protected from table reads executed in other blocks.

EBTR3 -- Table Read Protection bit (bitmask:0x08)

EBTR3 = ON

0xF7

Block 3 (001800-001FFFh) protected from table reads executed in other blocks.

EBTR3 = OFF

0xFF

Block 3 (001800-001FFFh) not protected from table reads executed in other blocks.

CONFIG7H (address:0x30000D, mask:0x40, default:0x40)

EBTRB -- Boot Block Table Read Protection bit (bitmask:0x40)

EBTRB = ON

0xBF

Boot block (000000-0001FFh) is protected from table reads executed in other blocks.

EBTRB = OFF

0xFF

Boot block (000000-0001FFh) is not protected from table reads executed in other blocks.

This page generated automatically by the device-help.pl program (2017-05-13 09:29:51 UTC) from the 8bit_device.info file (rev: 1.36) of mpasmx and from the gputils source package (rev: svn 1308). The mpasmx is included in the MPLAB X.